All Questions


Warning: Trying to access array offset on false in /home3/indiakep/public_html/wp-content/plugins/dw-question-answer/inc/Template.php on line 8
Filter:AllOpenResolvedClosedUnanswered
In a 3-ø bridge rectifier, the maximum conduction of each thyristor is
AnsweredRajasri Mundrathi asked 5 years ago • 
990 views1 answers0 votes
The most suitable power device for a higher frequency (above 100 kHz) switching application, select It from following.
AnsweredRajasri Mundrathi asked 5 years ago • 
1078 views1 answers0 votes
A snubber circuit is used to
AnsweredRajasri Mundrathi asked 5 years ago • 
1249 views1 answers0 votes
the fastest switching device, select one of the following
AnsweredRajasri Mundrathi asked 5 years ago • 
1026 views1 answers0 votes
Leakage current flows through the thyristor in
AnsweredRajasri Mundrathi asked 5 years ago • 
1002 views1 answers0 votes
Which device that does not have the gate terminal?
AnsweredRajasri Mundrathi asked 5 years ago • 
1193 views1 answers0 votes
The value of SCR for modern alternator is
AnsweredRajasri Mundrathi asked 5 years ago • 
981 views1 answers0 votes
A UJT is sometimes called_______ diode.
AnsweredRajasri Mundrathi asked 5 years ago • 
952 views1 answers0 votes
Self-inductance of magnetic coil is proportional to
AnsweredRajasri Mundrathi asked 5 years ago • 
879 views1 answers0 votes
Which of following is not a unit of flux?
AnsweredRajasri Mundrathi asked 5 years ago • 
895 views1 answers0 votes
The magnetism capacity of electromagnet will increase if the
AnsweredRajasri Mundrathi asked 5 years ago • 
1009 views2 answers0 votes
The Biot-savarts law is nothing but general modification of
AnsweredRajasri Mundrathi asked 5 years ago • 
868 views1 answers0 votes
The magnetic energy kept in an inductor is ______ current
AnsweredRajasri Mundrathi asked 5 years ago • 
825 views1 answers0 votes
The Ohm’s law for magnetic circuit is
AnsweredRajasri Mundrathi asked 5 years ago • 
913 views1 answers0 votes
In practical magnetic circuits, the air gap is kept
AnsweredRajasri Mundrathi asked 5 years ago • 
1048 views1 answers0 votes
Hysteresis is the phenomenon of
AnsweredRajasri Mundrathi asked 5 years ago • 
1082 views1 answers0 votes
The B-H curve is used to find the mmf of_____ in a magnetic circuit.
AnsweredRajasri Mundrathi asked 5 years ago • 
1511 views1 answers0 votes
The strength of an electromagnet is determined by
AnsweredRajasri Mundrathi asked 5 years ago • 
920 views1 answers0 votes
A magnetic field is produced by
AnsweredRajasri Mundrathi asked 5 years ago • 
992 views1 answers0 votes
A strong magnetic field is gives to a stationary electron. Then the electron
AnsweredRajasri Mundrathi asked 5 years ago • 
959 views1 answers0 votes
By increasing the number of turns 3 times in a toroid, the magnetic flux____
AnsweredRajasri Mundrathi asked 5 years ago • 
871 views1 answers0 votes
AT/m is the unit of
AnsweredRajasri Mundrathi asked 5 years ago • 
939 views1 answers0 votes
The source of magnetic field is
AnsweredRajasri Mundrathi asked 5 years ago • 
841 views1 answers0 votes
One weber is equal to
AnsweredRajasri Mundrathi asked 5 years ago • 
1040 views1 answers0 votes
The magnetic material used in permanent magnet is
AnsweredRajasri Mundrathi asked 5 years ago • 
1049 views1 answers0 votes
When magnet is heated
AnsweredRajasri Mundrathi asked 5 years ago • 
858 views1 answers0 votes
Which one formula is correct for electric field strength?
AnsweredRajasri Mundrathi asked 5 years ago • 
899 views1 answers-1 votes
What is the status of lines of force due to charged particles?
AnsweredRajasri Mundrathi asked 5 years ago • 
949 views1 answers0 votes
Biot-Savarts law states the relation among magnetic intensity and
AnsweredRajasri Mundrathi asked 5 years ago • 
828 views1 answers0 votes
Two straight parallel conductors carry equal currents in opposite direction. The force between them is
AnsweredRajasri Mundrathi asked 5 years ago • 
846 views1 answers0 votes
The field at any point on the axis of a current carrying coil will be
AnsweredRajasri Mundrathi asked 5 years ago • 
1145 views1 answers0 votes
Cork Screw rule is used to find
AnsweredRajasri Mundrathi asked 5 years ago • 
924 views1 answers0 votes
In the left hand rule, forefinger always denotes
AnsweredRajasri Mundrathi asked 5 years ago • 
861 views1 answers0 votes
The force among two long parallel conductors is inversely proportional to
AnsweredRajasri Mundrathi asked 5 years ago • 
966 views1 answers0 votes
Electric field intensity (E) at ant point in an electric field is equal to
AnsweredRajasri Mundrathi asked 5 years ago • 
831 views1 answers0 votes
Which of the following represents ohms law
AnsweredRajasri Mundrathi asked 5 years ago • 
887 views1 answers0 votes
The right hand instruction for defining the direction of the induced EMF was introduced by
AnsweredRajasri Mundrathi asked 5 years ago • 
773 views1 answers0 votes
Two parallel plates are placed at distance D charged by V volt. The field intensity E = _____
AnsweredRajasri Mundrathi asked 5 years ago • 
844 views1 answers0 votes
The mixture of iron oxide and aluminium oxide are used in thermit welding is
AnsweredRajasri Mundrathi asked 5 years ago • 
985 views1 answers0 votes
Preheating is essential in welding for
AnsweredRajasri Mundrathi asked 5 years ago • 
954 views1 answers-1 votes
Flash butt welding is
AnsweredRajasri Mundrathi asked 5 years ago • 
1081 views1 answers0 votes
Seam welding is a type of ____
AnsweredRajasri Mundrathi asked 5 years ago • 
980 views1 answers0 votes
Which type of electrode is used in submerged arc welding
AnsweredRajasri Mundrathi asked 5 years ago • 
1026 views1 answers0 votes
In resistance welding the electrode material is made of
AnsweredRajasri Mundrathi asked 5 years ago • 
1237 views1 answers0 votes
Arc stability is better with
AnsweredRajasri Mundrathi asked 5 years ago • 
1504 views1 answers0 votes
Arc length in arc welding should be equal to
AnsweredRajasri Mundrathi asked 5 years ago • 
1215 views1 answers0 votes
The temperature of plasma tourch is of the order of
AnsweredRajasri Mundrathi asked 5 years ago • 
1021 views1 answers-1 votes
Find which carbon steel is most weldable?
AnsweredRajasri Mundrathi asked 5 years ago • 
1204 views1 answers0 votes
Forge welding is best suited for
AnsweredRajasri Mundrathi asked 5 years ago • 
1297 views1 answers-2 votes
In arc welding, temperature of the following order may be granted
AnsweredRajasri Mundrathi asked 5 years ago • 
1094 views1 answers0 votes
Select one of the following which is strongest for brazing joints
AnsweredRajasri Mundrathi asked 5 years ago • 
1202 views1 answers0 votes
Equipment is used for arc welding a material by carbon electrode
AnsweredRajasri Mundrathi asked 5 years ago • 
1504 views1 answers-1 votes
In MIG welding, the metal is converted in the form of
AnsweredRajasri Mundrathi asked 5 years ago • 
1081 views1 answers0 votes
Distortion in welding occurs due to
AnsweredRajasri Mundrathi asked 5 years ago • 
1278 views1 answers0 votes
The most commonly used flame in gas welding is____
AnsweredRajasri Mundrathi asked 5 years ago • 
1142 views1 answers0 votes
Arc-welding uses following electric supply
AnsweredRajasri Mundrathi asked 5 years ago • 
3010 views1 answers4 votes
TIG welding is best suited for welding
AnsweredRajasri Mundrathi asked 5 years ago • 
1172 views1 answers1 votes
Projection welding is___
AnsweredRajasri Mundrathi asked 5 years ago • 
1020 views1 answers0 votes
for electrical resistance welding the surface of metal must be
AnsweredRajasri Mundrathi asked 5 years ago • 
943 views1 answers0 votes
After welding, the welded parts retain which properties responsible for that?
AnsweredRajasri Mundrathi asked 5 years ago • 
1008 views1 answers0 votes
1…910111213…62